Have you been in search of facts and techniques concerning A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily accessible, the task can move easily; if you need to open a wall surface to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either case, the job is within a home handyman's skills, although you will require an assistant to move out the old bathtub as well as set in the new one. Make sure you have certified yourself for the job as well as fit attempting it. Instead of employing a service provider to take over a halfway-completed task, it is far better to think about using one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This write-up will assist you set up a new bathtub in your shower room if you have currently acquired a new tub and also don't need to alter the arrangement of your previous water system pipes.
Your devices as well as product checklist ought to consist of the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, then the first thing you must do is detach the water system. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather bothersome due to the limited accessibility that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipelines. Once the supply pipelines have actually been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Prior to going on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap and the sink. Safeguard the faucet in position with the manufacturer supplied backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former kind needs to be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Using both wooden boards under its feet, position the bathtub in the needed placement. The wood boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little points.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bath tub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap port to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water supply and also inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill the bathtub and also inspect the overflow electrical outlet and also the typical electrical outlet for leakages.
Lastly, take care of the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the tub needs to wait till the tub has been utilized at the very least once as this will certainly settle it into its final setting.
Preparing for the Setup
To start with, the sustaining frame provided with the bath ought to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to stop stress on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its last placement.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, bring about difficulties with moisture and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to allow for the motion experienced when the tub remains in use. The sealant can fracture relatively very early if you do not think about this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece of writing on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing research the internet. Do you know another individual who is curious about Tools You Need to Install a New Bathtub ? Please feel free to share it. I cherish reading our article about How to Install a Bathtub Yourself.
Emergency plumber? One call away.